Thermoplastic
«Atlant and Atlant S»
Thermoplastics of a trade mark "Atlant" (hereinafter – TP "Atlant") is a composite material (bulk mix) based on an oil polymer binder containing pigments, fillers, plasticizers and functional additives. It contains glass beads in its composition. By customer's request, it can be produced without glass beads.
It is intended for application on the road surface of public roads with asphalt concrete pavement.
“Atlant” TP is available in white and yellow colours. Red colour can also be produced by customer's order.
It is intended for application on the road surface of public roads with asphalt concrete pavement.
“Atlant” TP is available in white and yellow colours. Red colour can also be produced by customer's order.
TERMS OF USE.
In its original form, it is a loose mixture, in order to achieve a working state, the thermoplastic must be melted to an operating temperature of 190° C-200° C. The application of road markings with thermoplastics is carried out in a mechanized way using special extruder marking equipment or manually using plastic markers.
INSTRUCTIONS FOR USE.
The consumption of TP “Atlant” when marking without a structural and profile surface is at least 6.5 kg / m2 with a layer thickness of 3 mm.
The consumption of glass beads is at least 300 g/m2, but can be increased depending on the road category or at the request of customers. Glass beads from 400 to 1500 microns are used to obtain the maximum retroreflective effect.
In its original form, it is a loose mixture, in order to achieve a working state, the thermoplastic must be melted to an operating temperature of 190° C-200° C. The application of road markings with thermoplastics is carried out in a mechanized way using special extruder marking equipment or manually using plastic markers.
INSTRUCTIONS FOR USE.
The consumption of TP “Atlant” when marking without a structural and profile surface is at least 6.5 kg / m2 with a layer thickness of 3 mm.
The consumption of glass beads is at least 300 g/m2, but can be increased depending on the road category or at the request of customers. Glass beads from 400 to 1500 microns are used to obtain the maximum retroreflective effect.
‘Atlant S’ thermoplastic spray (hereinafter referred to as ‘Atlant S’ TP spray) is a thermoplastic applied to the road surface by spraying. The composition contains glass beads (fraction 100-600 microns) in an amount from 20% to 30%.
It is intended for application on the road surface of public roads with asphalt concrete pavement. It is recommended to use it for renovation and restoration of markings made with thick-layer thermoplastics.
The ‘Atlant S’ spray is available in white and yellow colours.
It is intended for application on the road surface of public roads with asphalt concrete pavement. It is recommended to use it for renovation and restoration of markings made with thick-layer thermoplastics.
The ‘Atlant S’ spray is available in white and yellow colours.
TERMS OF USE
In its original form, it is a loose mixture, in order to achieve a working state, the thermoplastic must be melted to an operating temperature of 190° C -200° C. The application of road markings with thermoplastic spray is carried out by spraying.
INSTRUCTIONS FOR USE
For spray TP ‘Atlant S’, the consumption for marking devices is 1.7 kg/m2 with a layer thickness of 0.85 mm.
The consumption of glass beads is at least 300 g/m2, with a fraction from 125 to 600 microns.
In its original form, it is a loose mixture, in order to achieve a working state, the thermoplastic must be melted to an operating temperature of 190° C -200° C. The application of road markings with thermoplastic spray is carried out by spraying.
INSTRUCTIONS FOR USE
For spray TP ‘Atlant S’, the consumption for marking devices is 1.7 kg/m2 with a layer thickness of 0.85 mm.
The consumption of glass beads is at least 300 g/m2, with a fraction from 125 to 600 microns.
Important for the road marking brigades!
The air humidity during application should be not more than 65%
The time before application after precipitation is at least 12 hours
The air humidity during application should be not more than 65%
The time before application after precipitation is at least 12 hours
TRANSPORTATION AND STORAGE
Thermoplastics are stored in covered warehouses in their original packaging at a temperature of +5...+30 ° C, avoiding direct sunlight, moisture and water, in compliance with applicable fire safety regulations. The height of the stack when storing bags should not exceed 2 m.
Delivery time from 2 days, subject to availability in stock.
Production time from 2 days.
The guaranteed shelf life is 12 months from the date of manufacture.
Packaging - 20 kg polyethylene bags.
Delivery time from 2 days, subject to availability in stock.
Production time from 2 days.
The guaranteed shelf life is 12 months from the date of manufacture.
Packaging - 20 kg polyethylene bags.
If you want to purchase Thermoplastic, please make an order
Main office
53, Shcherbakovskaya str,
Moscow, Russia
Moscow, Russia
Contacts
+ 7 495 792 42 19
+375 29 723 40 25
(telegram, whatsapp)
sales@richchemical.ru
+375 29 723 40 25
(telegram, whatsapp)
sales@richchemical.ru
Manufacturing
17, Trudovaya str,
Kimry, Tverskaya region,
Russia
Kimry, Tverskaya region,
Russia
Make an order
Fill out the form below and our manager will contact you shortly
By clicking the button, you consent to the processing of personal data and agree to the privacy policy